; MainAX25-Stack — max25d daemon (Linux only)
; Copy to /etc/max25/max25d.ini or pass MAX25D_INI=

[features]
; PC-COM / SER12: max25-bcpr userspace (BayCom/based). Kernel baycom = legacy.
baycom = yes
pccom = yes
max25_bcpr = yes
; T-Modem-c1224 USB KISS half-TNC (Pico) — off unless stuffed
tmodem = no

[daemon]
; Operating mode: standalone | service | hybbx-main | hybbx-cohost | hybbx-host
; HyBBX attach (release serial/KISS to hybbxd): hybbx-main | hybbx-cohost | hybbx-host
;   or [hybbx] release_attach=yes on standalone
mode = standalone
; Drop to unprivileged user after stack prep (when started as root via run-max25d.sh)
; user = max25
; group = max25
; Default hardware when per-device hardware= is omitted
hardware = tncs
; Legacy single-device id (used when [devices] is absent)
device = tnc2c

[devices]
; Linux host: ONE RF device per max25d (design rule). Pick one id below.
; Layout examples still under design — do not enable two backends on one host.
; Serial path, baycom:<modem>, or crdop:<profile>
default = tnc2c
tnc2c = /dev/ttyS4
; pktnc2 = /dev/ttyS5
; --- PC-COM / BayCom/based: max25-bcpr userspace SER12 (default product path) ---
; Uncomment ONE RF device — max25e0 for PC-COM on ttyS0 (adjust serial in max25-bcpr.ini)
; default = max25e0
; max25e0 = max25-bcpr:bc0
; baycom-kiss = /dev/ttyUSB0
; pccom-kiss = /dev/ttyUSB0
; baycom-ser12 = baycom:a   ; LEGACY kernel path — avoid
; soft-crdop = crdop:default
; --- T-Modem-c1224 USB KISS half-TNC (not BayCom/based) ---
; tmodem = yes   ; under [features]
; tmodem = /dev/ttyACM0
; Acoustic bench (loopback / ALSA sniff / host daemon):
; audio-dummy = audio:loopback
; enabled = tnc2c   ; optional — single id recommended

[network]
; Terminal clients connect here (TCP). Unix socket always enabled on Linux.
tcp_host = 0.0.0.0
tcp_port = 7325
unix_socket = /run/max25/modem.sock
; Plain-text TCP auth for remote terminals (empty = disabled; Unix socket exempt)
tcp_password =

[modem]
; Default IDs — terminal may override live (session scope)
callerid = CB-0
callid = QST
; Send lines as AX.25 UI when yes (CRDOP uses native AX.25 UI display when ax25_ui=yes)
ax25_ui = yes
; Banned AX.25 source callsigns — silent RX drop (one per line in file)
; bans_file = /etc/max25/bans.txt

[reporting]
; Client-visible error/voice telemetry in STATUS (and EVENT on decode failure).
; yes = participate in STATUS; no = always report invalid for that field.
error_transmissions = yes
voice_transmissions = yes
; Data quality: N timed passes (good/bad only; voice/noise ignored), min % good.
; Each pass lasts up to data_pass_seconds (default 20s); full cycle = 3 × 20s.
data_passes = 3
data_quality_min = 50
data_pass_seconds = 20

[stack]
; Auto-start hardware on daemon start (boot-wait / baycom-pr-ctl / crdopc per device)
auto_start = yes
; TNC serial stability: periodic probe + software recovery (power-cycle stays rescue-only)
serial_watch = yes
serial_watch_interval = 60
serial_repair_cooldown = 20
serial_watch_startup_grace = 45
; max25d uses --recover-only for TNC stack prep (no power cycle on daemon start)
stack_recover_only = yes
stack_retry_interval = 120
; After N inline repair failures (error-host), escalate to boot-wait subprocess
serial_bootwait_escalate = yes
serial_bootwait_escalate_after = 3
serial_bootwait_escalate_cooldown = 300

; Software TOT (host policy for max25-bcpr / BayCom/based — not radio TOT)
; Synced into max25-bcpr.ini on stack start. Trip → stop bcpr, tot-paused, auto recover.
[tot]
enabled = yes
max_key_sec = 25
min_gap_sec = 1.5
max_consecutive = 3
max_bursts = 8
recover_sec = 300

; Detached operator session (CLI — not parsed from ini):
;   max25d --session tmux -c /etc/max25/max25d.ini
;   max25d session start --tmux
;   max25d-session attach
; Env: MAX25D_SESSION=max25d  MAX25D_SESSION_BACKEND=tmux|screen

[serial]
; Legacy single-device overrides — ignored when [devices] is present.
; device = /dev/ttyS4
; baud = 19200
; line = 8n1
; dtr_rts = yes
; kiss_entry = kiss_on

[serial.tnc2c]
; Per-device serial profile (optional — defaults from stacks/tncs/tnc2c-serial.env)
; baud = 19200
; line = 8n1
; dtr_rts = yes
; kiss_entry = kiss_on

[serial.pktnc2]
; pktnc2: 9600 8N1, DTR+RTS off, kiss_entry=auto
; baud = 9600
; line = 8n1
; dtr_rts = no
; kiss_entry = auto

[serial.tmodem]
; T-Modem-c1224 USB CDC KISS half-TNC (not BayCom/based)
; baud = 115200
; line = 8n1
; dtr_rts = no

; --- BayCom kernel (LEGACY — prefer bcpr above) ---
; baycom-ser12 = baycom:a
; [device.baycom-ser12]
; kiss_link = /var/run/baycom-pr/kiss
; modem = a
; baycom_ini = /etc/baycom/baycom-pr.ini

; --- max25-bcpr device block (when max25e0 enabled above) ---
; [device.max25e0]
; kiss_link = /tmp/max25-bcpr/kiss-bc0
; max25_bcpr_ini = /etc/max25/max25-bcpr.ini
; ipv4 = 127.0.0.25/8
; ipv6 = ::25/128
; Forks max25e0:bcN inherit ipv4/ipv6 from max25e0 unless overridden.
; Built by default (MAX25_BUILD_MAX25_BCPR=ON). See share/max25-bcpr/max25-bcpr.ini.example

; --- HyBBX co-host / standalone attach (max25d preps, HyBBX opens KISS) ---
; [hybbx]
; release_attach = yes

; --- USB/async BayCom KISS serial ---
; [serial.baycom-kiss]
; baud = 9600
; line = 8n1
; dtr_rts = no

; --- CRDOP sound-card modem (MAX25-SoftModem) ---
; [device.soft-crdop]
; host = 127.0.0.1
; port = 8515
; listen = yes

; --- Virtual IP netdev (TUN max25d0 — planned near term) ---
; Full doc: docs/NETDEV.md · interface name is always max25d0
; [netdev]
; enabled = no
; mode = tun
; ipv4 = 127.0.0.25/8
; ipv6 = ::25/128